Book

 

This great article which follows on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is immensely attention-grabbing. Don't miss out on it.

Setting up a bathtub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately challenging task. If the old tub is easily obtainable, the job can move quickly; if you need to open up a wall to get rid of the old tub and also place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will require a helper to leave the old bathtub and set in the brand-new one. Make sure you have qualified on your own for the work and are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed task, it is better to think about utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you mount a brand-new tub in your shower room if you have currently acquired a brand-new bathtub as well as don't require to change the arrangement of your previous water supply pipelines.
Your tools and product checklist should consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Removing Old Touches

If you need to change old faucets with new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to going on to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Fitting New Taps

If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Protect the tap in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type needs to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Installing the Tub

Using both wood boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto four tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub till the level checks out level.
To install taps, fit the bottom of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the supply of water and examine all joints as well as brand-new pipework for leaks and tighten them if needed. Fill up the bathtub and also inspect the overflow outlet and also the typical outlet for leakages.
Finally, fix the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bathtub ought to wait up until the bath tub has been made use of a minimum of when as this will certainly settle it right into its last position.

 

 

Planning for the Installation

First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to avoid strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last placement.

 

 

Tiling Around the Bath tub

In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and the tiling, leading to issues with moisture and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes and also cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can crack fairly early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We hope you enjoyed reading our post on How to Install a Bathtub Yourself. Many thanks for spending some time to read our posting. So long as you liked our blog entry plz be sure to share it. I treasure reading our article about How to Install a Bathtub.

Dial, we deliver!